Olympia Chimney Flue Liner Replacement Nationwide

Olympia Chimney Flue Liner Replacement: The Orland Park Owner’s Guide

Olympia Chimney flue liner replacement in Orland Park typically runs $2,800-$5,200 installed, depending on flue diameter, height, and whether the chase needs modification. We stock Olympia Chimney-compatible stainless steel liners in common diameters from 5.5″ to 8″ and can usually inspect, measure, and install within a single booked visit. Emberly Chimney Cleaners Orland Park is an independent service provider, not affiliated with Olympia Chimney.

Call (708) 294-2571

Most Orland Park homeowners discover the problem during a routine sweep or after a chimney fire scare. The liner shows gaps between sections, the stainless has pinholed through, or the original clay tiles have shifted and opened a direct path for heat and combustion gases into the chimney structure. In the older homes near Centennial Park, we regularly see original clay liners that were never meant to handle the sustained burns from modern EPA-certified stoves.

Corrine Halstead, our owner, puts it this way: “The camera goes in first. The price comes after.” That means we show you the footage before quoting a single number.

Which Olympia Chimney Models This Applies To

Olympia Chimney manufactured several liner series, and the part you need depends on what was originally installed. The Olympia 316Ti flexible liner, their standard residential line, came in diameters from 5.5″ to 8″ with either a .006″ or .012″ wall thickness. The heavier wall was spec’d for wood boiler and coal applications, which we still see in some Orland Park basements. If your original liner has an Olympia tag, it usually sits just above the first flue tile or stamped into the top collar.

Here’s where owners get tripped up: Olympia used two different end-ring designs across production years. The pre-2012 snap-lock ring and the post-2012 compression-fit ring are not interchangeable, and forcing the wrong collar onto an existing top plate cracks the seal. We carry both styles in our Orland Park warehouse, along with HeatShield and DuraFlex equivalents that match Olympia’s 316Ti spec when the original part is no longer manufactured.

To identify yours, check the metal tag inside the firebox throat or measure the flue opening with a tape measure. Clay flues are nominal sizes, so a labeled “6-inch” clay flue often measures closer to 6.75″ inside. We size liners to the actual inside dimension, not the nominal callout.

Signs Your Olympia Chimney Flue Liner Replacement Is Failing

• White or tan staining on exterior brick. This is efflorescence from moisture and combustion gases migrating through cracked tiles or liner gaps. In Orland Park’s freeze-thaw cycles, that moisture expands and accelerates spalling on the chimney face.
• Bits of clay tile in the firebox or cleanout. The original terra cotta liner is delaminating. Once tiles start shedding, the flue has lost its structural integrity and can no longer contain a chimney fire.
• Smoke odor in upstairs rooms during heavy rain. A separated liner joint or corroded section lets water and draft reversal enter the chase. We see this most often on south-facing chimneys in Orland Park where thermal cycling is hardest on the metal.
• Visible gaps or daylight through the flue wall during flashlight inspection. Any opening larger than a pencil eraser allows creosote to build on the brick and creates a direct ignition path to the framing. This is what NFPA 211 calls an “immediately hazardous” condition.
• Carbon monoxide detector alerts near the fireplace. A compromised liner can reverse draft or leak combustion gases into wall cavities. This symptom demands same-week attention, not next-season scheduling.

Before

After

Replacement Cost & What’s Included

The range depends on three things we measure on site: actual flue height from appliance throat to top plate, whether the existing top plate and rain cap can be reused or must be replaced, and whether the chimney chase is straight or has offsets that require additional labor. Every quote is delivered in writing before work starts, with the scope, materials list, and warranty spelled out. That’s Haven Standard Clause 1.

What you get: the liner, proper insulation per manufacturer spec, a new top plate and collar where needed, full camera documentation of the completed installation under Haven Standard Clause 4, and our 365-Day Done Right Promise. Materials come through our buying network, which includes Olympia Chimney, DuraFlex, HeatShield, and Gelco, so we’re not marking up a single-source part.

DIY or Call Us?

There’s a safe middle ground here. You can verify your liner diameter with a tape measure, check the metal tag for series information, and photograph any visible damage from the firebox. That saves us time and you money.

What you should not do: climb the roof, drop a liner yourself, or attempt to break out clay tiles without containment. A 25-foot stainless liner column weighs 80-120 pounds and requires controlled lowering with a winch or cable system. The top plate seal involves high-temperature silicone and proper overlap geometry; a gap of even 1/8″ will leak condensation into the chase within two heating seasons. And if original clay tiles must be removed, the debris falling down an uncontrolled flue can crack the smoke shelf or damage the damper assembly.

We carry Olympia Chimney-compatible liners, collars, and top plates on our Orland Park trucks. Call (708) 294-2571 and we’ll book a camera inspection. You’ll see what we see before we name a price.

FAQs